You can configure the file size display: bytes or dynamic (bytes, kB, MB, depending on the size). No personal information is collected (see our Privacy Policy for details). help us improve the software by sending usage statistics. Send anonymous usage statistics to Electronic Team, Inc. When this option is disabled, an item will be deleted permanently. When this option is enabled and you click Shift+F8, a file will be deleted permanently. Move to trash: If enabled, an item will be deleted to Trash when using the Delete keyboard key, or F8, or the Delete button in the lowest right corner of the app's window. Use + on numeric keypad only for files selection: Select only files using Num+ (Select item) and Cmd+Num+ (Select All), otherwise both files and folders will be selected.Ĭalculate folder size on Space: Show the size of folders when clicking the space bar. If enabled, you will always go to the root folder when you change disks. Go root when changing drive: When disabled, Commander One remembers the path when you change disks and you will get back to the same folder when you switch back to the disk. View files with: View files using either the built-in file viewer (default), QuickLook, or Preview.Įdit files with: Choose the text editor to be used when you open a file for editing. There is generally no right way to play with Commander, the main advice is take your time, and start slowly.Ĭommander 3 also now has the ability to record and playback sessions via the Session Recorder.Modified on: Tue, 27 Jun, 2023 at 5:13 PM Using Commander can be considered to a bit of an art form, similar to that of playing a musical instrument. Output Map control is a beta function and not currently available. Audio and System modes are not selectable. Power Level allows you to control the overall power level of your 2B - Low or High, while Program Mode allows you to select which program mode the 2B is running in. Power Level Control, Map Control and Program Mode Control. Depending on the mode selected only one might be shown, and depending on the mode the sliders might be labelled differently. The feel and rate sliders operated in the same way as the power sliders. Next we have a Rate Slider and a Feel Slider. This is part of the new Session Record / PlayBack System. Off, Stop and Playback/Record Controlsįurther down the screen can be seen a large stop button, which when pressed drops both the outputs to zero, and record, Stop and Pause button, together with out Stop and Pause buttons. Clicking on a slider will jump the value to that point. Dragging on the slider will change the value on the corresponding Channel, but the value is only sent to the 2B with the slider is released. Two power sliders for Channel A and Channel B, together with a value displayed for each channel. On the left is a battery icon indicating roughly the state of charge on your 2B, followed by the version number of the firmware the 2B is running, followed by '2B Connected'.įrom the top of the screen down you should see Power Sliders If you have successfully connected the 2B to Commander, you should see an update on the bottom of the application. You may find you need to install the drivers for the Digital Link Interface, instructions for this can be found. If you do not see the digital link connection, then check your connections to your Mac, and then check your. Commander should then connect to your 2B and you will then see a status update on the bottom of the application. Using the drop down at the bottom left of the screen, select the serial port the 2B is connected to it should start 'usbserial-'. this indicates that Commander has not yet been linked to your 2B. Once Commander is running you will be presented with the main screen.Īt the bottom of the screen you will see 2B not connected. It is safe to ignore this warning as it will only appear once, and click Open to run Commander 3. Instructions on how to put your 2B into Commander mode can be found at How do I select Commander?Ĭlick on the Commander Icon in LaunchPad.Īs the file has been downloaded from the internet you might get an additional warning. The display will show the arrow on the display indicating that your 2B is in Commander Mode (see below). Plug in the Digital Link Interface into a spare USB port on your computer, then plug in your 2B to the Digital Link Interface, ensure Commander is switched on if necessary, if you are using Firmware 2.106 or newer you will not need to do anything to turn it on.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |